Comments on: The Advantages Of New Fibre Laser Welding Techniques http://www.alamoweldingsupply.com/2007/03/the-advantages-of-new-fibre-laser-welding-techniques/ Everything about Welding Fri, 28 Jan 2011 12:17:03 +0000 hourly 1 http://wordpress.org/?v=3.3.1 By: Theory1 http://www.alamoweldingsupply.com/2007/03/the-advantages-of-new-fibre-laser-welding-techniques/comment-page-1/#comment-1644 Theory1 Sat, 03 Mar 2007 20:34:29 +0000 http://www.alamoweldingsupply.com/2007/03/the-advantages-of-new-fibre-laser-welding-techniques/#comment-1644 Welding supply will have compressed nitrogen but never liquid nitrogen. Try a machine shop that works with soft rubber products. They use the liquid nitrogen to harden the rubber so they can machine it accurately with out it stretching all over the place. Welding supply will have compressed nitrogen but never liquid nitrogen.

Try a machine shop that works with soft rubber products.
They use the liquid nitrogen to harden the rubber so they can machine it accurately with out it stretching all over the place.

]]> By: rajev v http://www.alamoweldingsupply.com/2007/03/the-advantages-of-new-fibre-laser-welding-techniques/comment-page-1/#comment-1647 rajev v Sat, 03 Mar 2007 13:16:06 +0000 http://www.alamoweldingsupply.com/2007/03/the-advantages-of-new-fibre-laser-welding-techniques/#comment-1647 around 300 watts. around 300 watts.

]]> By: KEV88 http://www.alamoweldingsupply.com/2007/03/the-advantages-of-new-fibre-laser-welding-techniques/comment-page-1/#comment-1646 KEV88 Sat, 03 Mar 2007 12:24:38 +0000 http://www.alamoweldingsupply.com/2007/03/the-advantages-of-new-fibre-laser-welding-techniques/#comment-1646 Try: Gordon Woods Industrial Welding Supplies 7254 Coldwater Canyon Ave. North Hollywood. Ca. 91605 Tel 818-759-6900 or Altair Gases and Equipment 5508 Vineland Ave. North Hollywood, Ca 91601 Tel 818-760-2011 Try:

Gordon Woods Industrial Welding Supplies
7254 Coldwater Canyon Ave.
North Hollywood. Ca. 91605
Tel 818-759-6900

or Altair Gases and Equipment
5508 Vineland Ave.
North Hollywood, Ca 91601
Tel 818-760-2011

]]> By: Barcadcadacada http://www.alamoweldingsupply.com/2007/03/the-advantages-of-new-fibre-laser-welding-techniques/comment-page-1/#comment-1641 Barcadcadacada Fri, 02 Mar 2007 17:45:44 +0000 http://www.alamoweldingsupply.com/2007/03/the-advantages-of-new-fibre-laser-welding-techniques/#comment-1641 It's possible you do not own the tanks. Some companies rent the filled container to the customer and retain ownership of the container. Check there is no supplier name on them. If there is ring them and find out how they supply. It's possible you do not own the tanks. Some companies rent the filled container to the customer and retain ownership of the container. Check there is no supplier name on them. If there is ring them and find out how they supply.

]]> By: michelle w http://www.alamoweldingsupply.com/2007/03/the-advantages-of-new-fibre-laser-welding-techniques/comment-page-1/#comment-1643 michelle w Fri, 02 Mar 2007 03:59:31 +0000 http://www.alamoweldingsupply.com/2007/03/the-advantages-of-new-fibre-laser-welding-techniques/#comment-1643 That's more than likely the distributor, not the manufacurer. Lincoln is probably the actual manufacturer. That's more than likely the distributor, not the manufacurer.
Lincoln is probably the actual manufacturer.

]]> By: Hope H http://www.alamoweldingsupply.com/2007/03/the-advantages-of-new-fibre-laser-welding-techniques/comment-page-1/#comment-1645 Hope H Thu, 01 Mar 2007 09:25:55 +0000 http://www.alamoweldingsupply.com/2007/03/the-advantages-of-new-fibre-laser-welding-techniques/#comment-1645 In general, heat-treated mild steels are arc welded without pre-heat. However, a preheat should be used when the metal temperature is below about 50 degrees F (10 degrees C), and a preheat of about 100 degrees F (38 degrees C) or higher should be used if the plate thickness is over 1 in. (25.4 mm) or if the joint is highly restrained. In general, heat-treated mild steels are arc welded without pre-heat. However, a preheat should be used when the metal temperature is below about 50 degrees F (10 degrees C), and a preheat of about 100 degrees F (38 degrees C) or higher should be used if the plate thickness is over 1 in. (25.4 mm) or if the joint is highly restrained.

]]> By: savehumanity http://www.alamoweldingsupply.com/2007/03/the-advantages-of-new-fibre-laser-welding-techniques/comment-page-1/#comment-1640 savehumanity Thu, 01 Mar 2007 08:58:21 +0000 http://www.alamoweldingsupply.com/2007/03/the-advantages-of-new-fibre-laser-welding-techniques/#comment-1640 The machine was never intended for such usage. The machine was never intended for such usage.

]]> By: welder1 http://www.alamoweldingsupply.com/2007/03/the-advantages-of-new-fibre-laser-welding-techniques/comment-page-1/#comment-1642 welder1 Thu, 01 Mar 2007 08:17:21 +0000 http://www.alamoweldingsupply.com/2007/03/the-advantages-of-new-fibre-laser-welding-techniques/#comment-1642 you may want to do a search on that (google). That may give u the help u need. Good luck! you may want to do a search on that (google). That may give u the help u need. Good luck!

]]> By: gdkul http://www.alamoweldingsupply.com/2007/03/the-advantages-of-new-fibre-laser-welding-techniques/comment-page-1/#comment-1639 gdkul Thu, 01 Mar 2007 07:54:53 +0000 http://www.alamoweldingsupply.com/2007/03/the-advantages-of-new-fibre-laser-welding-techniques/#comment-1639 There realy isn't a "two phase". There is single phase that has a neutral wire - sometimes called "split phase". If you only have 3 phase available, they you may have a problem trying to get 240 volts for a welder. You may need a transformer for this. There realy isn't a "two phase". There is single phase that has a neutral wire – sometimes called "split phase".

If you only have 3 phase available, they you may have a problem trying to get 240 volts for a welder. You may need a transformer for this.

]]>